CRA harmonised standards: EN 40000, ETSI EN 304 and IEC 62443-based profiles

Harmonised standards give products that follow them a presumption of conformity with the Cyber Resilience Act's essential requirements, but only once their references are published in the Official Journal. Under request M/606, CEN, CENELEC and ETSI are drafting horizontal, product-category and operational-technology standards.

By the Vellaci teamPublished Updated 7 min readOperational guidance, not legal advice

Share:LinkedInXE-mail

Key facts

Legal effect
Presumption of conformity for the requirements covered, once cited in the Official Journal (Art. 27(1))
Request
Standardisation request M/606 to CEN, CENELEC and ETSI
Horizontal
EN 40000-1-x (CEN-CENELEC JTC 13 WG 9): vocabulary, principles and risk management, vulnerability handling, generic security requirements
Product categories
ETSI EN 304 617 to EN 304 636 (TC CYBER EUSR) for most Annex III categories
Operational technology
CENELEC TC 65X security profiles based on IEC 62443, such as prEN 50770-5 for routers, modems and switches
Status reviewed
20 October 2026 — stages change monthly; check the ESO records before relying on them

Why harmonised standards matter for the CRA

Article 27(1) presumes that products and processes conforming to harmonised standards — or parts of them — whose references are published in the Official Journal conform with the essential requirements those standards cover. The presumption is the practical value: it turns 'show that you meet Annex I' into 'show that you applied this standard'. Where standards are missing or insufficient, the Commission may adopt common specifications by implementing act (Article 27(2)).

Standards also decide routes. An important Class I product may use internal control (Module A) only if harmonised standards, common specifications or a European cybersecurity certification scheme at assurance level at least 'substantial' are applied in full; otherwise it needs a notified body (Article 32(2)). And Annex VII point 5 requires the technical documentation to list the standards applied in full or in part — or describe the solutions adopted where none were applied.

Three layers of standards

The M/606 work programme published by CEN, CENELEC and ETSI in April 2025 organises the work in layers, matched to lines of the Commission's request.

LayerWho draftsReferencesCovers
Horizontal (all products)CEN-CENELEC JTC 13 WG 9EN 40000-1-1 to 1-4Vocabulary, principles and risk management, vulnerability handling, generic security requirements
Product categories (Annex III)ETSI TC CYBER EUSR; CEN/TC 224 and CLC/TC 47X for the identity-management and chip categoriesEN 304 617 to EN 304 636 and othersCategory-specific requirements, one standard per category
Operational technology profilesCLC/TC 65X WG 3prEN 50770 series; amendments to EN IEC 62443-4-1, 4-2 and 3-3IEC 62443-based profiles for six categories used in OT environments
Critical products (Annex IV)CEN/TC 224, CEN-CLC/JTC 13 WG 6, CLC/TC 47XTo be numberedHardware security boxes, smart meter gateways, smartcards and secure elements

Horizontal standards: the EN 40000-1 series

Status as recorded in the CEN-CENELEC project records and the M/606 work programme at the review date.

PartTitleStatus at review dateOfficial Journal citation
EN 40000-1-1VocabularyDraft (prEN)Not stated
EN 40000-1-2Principles, product risk management, and lifecycle activitiesUnder approval; ratification scheduled for 2 November 2026No citation expected
prEN 40000-1-3Vulnerability handlingUnder approvalCitation expected
EN 40000-1-4Generic security requirements (Annex I Part I point (2))Drafting; planned adoption by 30 October 2027 in the April 2025 work programmeNot stated

Product-category standards: the ETSI EN 304 series

ETSI's technical committee CYBER drafts one standard per Annex III category in its EUSR working group. All of the following were available as public enquiry drafts on ETSI's open document server, dated between June and August 2026; drafts at enquiry stage can still change substantially.

StandardAnnex III categoryClass
EN 304 617Standalone and embedded browsersI
EN 304 618Password managersI
EN 304 619Software that searches for, removes or quarantines malicious softwareI
EN 304 620Products with the function of a virtual private network (VPN)I
EN 304 621Network management systemsI
EN 304 622Security information and event management (SIEM) systemsI
EN 304 623Boot managersI
EN 304 624Public key infrastructure and digital certificate issuance softwareI
EN 304 625Physical and virtual network interfacesI
EN 304 626Operating systemsI
EN 304 627Routers, modems intended for the connection to the internet, and switchesI
EN 304 631Smart home general purpose virtual assistantsI
EN 304 632Smart home products with security functionalitiesI
EN 304 633Internet-connected toys with social interactive or location tracking featuresI
EN 304 634Personal wearables for health monitoring or for childrenI
EN 304 635Hypervisors and container runtime systemsII
EN 304 636Firewalls, intrusion detection and/or prevention systemsII

Categories outside the ETSI series

The work programme assigns the remaining Annex III and IV categories to other committees: identity management and privileged access management to CEN/TC 224; microprocessors, microcontrollers, ASICs and FPGAs with security-related functionalities, and tamper-resistant microprocessors and microcontrollers, to CENELEC TC 47X; hardware devices with security boxes to CEN/TC 224; smart meter gateways to CEN-CENELEC JTC 13 WG 6; and smartcards and secure elements to CENELEC TC 47X and CEN/TC 224. Their reference numbers were to be defined when the work items were activated.

OT profiles based on IEC 62443: the prEN 50770 series

For six Annex III categories that are common in industrial environments — firewalls and intrusion detection or prevention systems, network management systems, network interfaces, VPN products, routers, modems and switches, and SIEM systems — CENELEC TC 65X WG 3 is drafting security profiles that select a defined subset of IEC 62443 requirements, in parallel with the ETSI standards for the same categories. prEN 50770-5, 'Security for Operational Technologies – Part 5: Security Profile for routers, modems intended for the connection to the internet, and switches (based on EN IEC 62443)', is the one for routers, modems and switches.

The same committee is preparing CRA-related amendments to EN IEC 62443-4-1 (secure product development lifecycle), 62443-4-2 (technical requirements for components) and 62443-3-3 (system requirements). For an OT manufacturer with an existing 62443 programme, the profiles are the most direct path; the choice between a profile and the ETSI standard for the same category should follow the product's intended operational environment and be recorded in the technical documentation.

What to do before the standards are cited

  1. Map each product to the standards that will apply to it: the horizontal series always, plus the product-category standard or OT profile for its Annex III category, if any.
  2. Align with the state of the art now — IEC 62443-4-1 and 4-2, ETSI EN 303 645 for consumer IoT, ISO/IEC 29147 and 30111 — and record the mapping, because Annex VII asks for the solutions adopted where no harmonised standard was applied.
  3. Read the public drafts that concern you and comment through your national standards body during enquiry; that is the only stage where manufacturers can still shape them.
  4. For Class I products, plan a notified-body route until the relevant standard is cited, and switch to internal control only once the citation exists and you apply it in full.
  5. Re-check citations before every conformity assessment; a standard applied 'in part' gives a presumption only for the parts applied.

Frequently asked questions

Are there harmonised standards for the CRA yet?
At this guide's review date (20 October 2026) we found no CRA harmonised standard cited in the Official Journal. EN 40000-1-2 was scheduled for ratification on 2 November 2026 without an expected citation, prEN 40000-1-3 on vulnerability handling was under approval with a citation expected, and the ETSI product-category standards were public enquiry drafts.
What is prEN 50770-5?
A CENELEC draft, prepared by TC 65X under the CRA standardisation request, that defines a security profile based on EN IEC 62443 for routers, modems intended for the connection to the internet, and switches used in operational-technology environments. ETSI's EN 304 627 covers the same Annex III category for general use.
Is IEC 62443 a harmonised standard under the CRA?
Not as such. IEC 62443 is a voluntary international standard. Under M/606, CENELEC is preparing CRA amendments to EN IEC 62443-4-1, 4-2 and 3-3 and IEC 62443-based profiles; only the references actually published in the Official Journal will give a presumption of conformity.
Can a Class I product use self-assessment before standards are cited?
Only if it applies in full a cited harmonised standard, a common specification or a European cybersecurity certification scheme at assurance level at least 'substantial'. Without one of those, Article 32(2) requires EU-type examination (Modules B and C) or full quality assurance (Module H) with a notified body.
What does 'no citation expected' mean for EN 40000-1-2?
That the standard is not expected to be listed in the Official Journal as a harmonised standard under the CRA, so applying it will not by itself create a presumption of conformity. It remains a useful, consensus description of risk management and lifecycle principles to reference in the technical documentation.

Know which standard each product will be measured against.

Classify every product against Annex III and IV, see its conformity route, and keep the standards mapping with its technical documentation.